Materials List
Bill of Materials
-----------------
First draft 5-7-13.
Tom Gibson
*'d items need more study. Specifics at the end.
Frames
------
frames 1 4x8x3/4 marine plywood
deck cleats 5' 4x3/4 solid wood
side cleats 6' 2x2 solid triangular
Bow
---
Bow 3' 4x4 solid
Chines 10' 1x10 solid
Stem 5' 4x10 solid (pair of 2x10's?)
Post 3' 4x4 solid
Transom
-------
planking 1 plywood 3/4, 14" x 50"
frame 6' 1x4 solid
Hull
----
side planks 4 plywood 3/4
bottom planking 6 plywood 3/4
bow planking 1 plywood 3/4 cut to planks
OR
3 plywood 1/4 4x5 each
butt blocks 32' 3/4 plywood outer ply grain ACROSS, not
lengthwise. Cut from Frame sheets. 6" wide
chine log 48' 1x2 solid (scarfed, station 4 to AP)
sheer clamp 60' 1x2 solid (scarfed, FP to AP)
skeg 10' x 2 x 8 solid (15" x 10' triangle)
keel 12' x 2 x 10 solid
molds 10 2' x 2.5' x 3/4" cdx plywood
Decking/Tholepins
-----------------
decking
fore 2 3/4" plywood, 2-6 x 4-6 (30"x54")
aft 1 3/4" plywood, 4-9 x 2-0 (57"x24")
*1 sides 40'x4" curved to fit 3/4" plywood
coamings solid or maybe plywood with edge molding
*2 fore/aft 2 5'x8"x3/4
*2 sides 42' x 1 x 5
tholepin mounts 4' x 3 x 3 solid
Thwarts/Benches
---------------
*3 solid 42' 2x10 solid
*3 bracing 60' 2x2 solid
Lee Boards
----------
*4 board 2 52" x 16" x 6/4" (2 plys thick)
*5 mount 2 3"x4"x16" white oak for strength
hardware 2 T-bolt, straps, etc
tackle 2 blocks, line, cleat, 7x7 wire and nico-press
*5 chine rub board 2 2x4x6'
Rudder
------
*6 blade 48" x 10 x 3/4
cheeks 2 36" x 10 x 3/4
pivot bolt 3" x 3/8" + washers + self locking nut
tiller 6' x 2 x 6
gudgeons and pintles skeg pintle, transom pintle, 2 9/4" gudgeons.
*6 lifting hardware
Hatches
-------
fore/aft 2 2' x 5' 3/4 ply
Fastenings/Glue/Glass
---------------------
*7 how much???
Other hardware
--------------
*8 what???
More Study
==========
*'d items have the following questios...
1. decking sides cut lines will be taken off the finished hull. But we need an
estimate of the plywood.
2. Fore/aft and side coamings -- need to verify dimensions
3. Thwarts/Benches -- need detail design for the bracing
4. Lee boards -- are these dimensions satisfactory.
5. mount and chine rub boards -- need a detailed design.
6. rudder blade -- is 3/4 inch ok. Detailed design needed for lifting hardware.
7. how much fabric, glue, fastenings?
8. What other hardware??
Back to: Building a new Garvey
